Germinario et al. Herit Sci (2017) 5:44 DOI 10.1186/s40494-017-0156-z RESEARCH ARTICLE Trachyte weathering in the urban built environment related to air quality Luigi Germinario1* , Siegfried Siegesmund2, Lara Maritan1, Klaus Simon2 and Claudio Mazzoli1 Abstract Decay of trachyte used as building stone in urban environment was investigated through the analysis of crusts and patinas found on trachyte of the Euganean Hills in the Renaissance city walls of Padua, northeastern Italy. Mineral- ogical and microstructural characteristics of the alteration products, as well as major- and trace-element chemical composition, were determined by optical microscopy, SEM–EDS and X-ray mapping, XRPD, and LA-ICPMS. The results are discussed referring to environmental parameters, in particular concerning air quality and anthropic pollution sources. The influence of composition of the stone and other neighboring materials on specific weathering processes is also debated. The formation of crusts and patinas turns out to be mainly due to exogenous processes. Enrichment in heavy metals and carbonaceous matter derives from the deposition of particulate emitted during fuel combus- tion by road vehicles, domestic heating and, secondarily, industrial activities. The particulate is typically cemented by calcite, mainly mobilized after dissolution from nearby mortar joints, or iron, released by leaching from iron-bearing minerals, reprecipitated according to pH fluctuations. Gypsum layers were rarely observed. Generally, composition of the weathering crusts and patinas of Euganean trachyte proves to be an informative marker for the relevant environ- mental conditions and their evolution. Keywords: Building stone decay, Air pollution, Weathering crust, Mortar dissolution, Leaching, Mineral mobilization, Euganean trachyte © The Author(s) 2017. This article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The Creative Commons Public Domain Dedication waiver (http://creativecommons.org/ publicdomain/zero/1.0/) applies to the data made available in this article, unless otherwise stated. Introduction Air quality is a key factor affecting stone weathering in urban environment, where concentration of stoneworks is generally large and, at the same time, human activities are intense and diverse. The latter change in time and space, and so does their contribution to pollution. Time variations in quantity and quality of pollutant emissions strongly depend on changes in fuel use [1]. SO2 emissions have represented a major concern until the 20th century, but considerably declined in Europe during the last dec- ades, by one or two orders of magnitude in cities, deter- mining a general improvement of air quality [2]; however, globally, increasing coal demand according to recent pro- jections [3–5] and, for example, the latest changes in cli- mate policies in the USA [6], may revert this tendency. Nowadays, the higher concentration of other pollutants, such as N oxides (NOx), particulate matter (PM), and O3, must be reassessed. Road transport, domestic heat- ing, industry, and power plants are the main pollution sources in urban areas, but their relative importance has changed with time as well [7]. In the modern urban environment, a multi-pollutant scenario arises with a major incidence of airborne par- ticulate, having high concentration of elemental C (soot) and volatile organic compounds (VOC), with fuel com- bustion from road traffic as the main contributor [8, 9]. This carbonaceous matter exhibits high specific surface area and contains heavy metals and aluminum–sili- con particles, which act as catalysts and adsorbents for organic compounds [10]. Pollutant interaction with stone preferentially occurs through short-range dry deposition. Overall, the well-known processes of crust formation are becoming less significant in favor of soiling, character- ized by an increasing enrichment in organic C, i.e., ali- phatic and polycyclic aromatic hydrocarbons [11–14]. In Open Access *Correspondence: luigi.germinario@gmail.com 1 Department of Geosciences, University of Padova, Via Gradenigo 6, 35131 Padua, Italy Full list of author information is available at the end of the article Page 2 of 17Germinario et al. Herit Sci (2017) 5:44 urban environment, dry deposition is more significant than wet deposition, but a notable danger is still repre- sented by short drizzles, fog, and dew, which have higher pH, do not remove previous acid deposits, and provide sufficient moisture for their chemical activation [15–17]. Most studies on the interaction between building stone and urban environment have focused so far on weather- ing of carbonate rocks, their dissolution, and formation of gypsum crusts [18]; other rock types have been investi- gated more rarely. Deterioration of trachyte has also received scarce atten- tion in the literature, not only because of its generally good durability. In fact, its use is historically less com- mon if compared to other volcanic rocks, i.e., tuff above all, andesite, and basalt. These rock types have been quarried in Europe, Latin America, Middle and Far East and so on, and employed by some of the most important ancient civilizations, like the Romans, Egyptians, Greeks, Incas, and Aztecs [19, 20]. Trachyte use has not been such widespread, with an exploitation mostly limited to Europe, namely Italy, Germany, Czech Republic, and France, as well as the Azores and Canary Islands. Most studies on trachyte weathering have focused on coastal salt-aggressive environments, such as those of Venice and Naples in Italy, and the Azores islands. Several deterioration patterns have been observed, including scaling, powdering, exfoliation, blistering, dif- ferential erosion, and efflorescence. They result to be mainly determined by cyclic processes of in-pore salt crystallization related to sea-salt supply. The phases involved are halite, gypsum, thenardite, and mirabilite and, in indoor environments, also trona and natron [21– 24]. Only Lazzarini et al. [23] have addressed in detail the on-site decay of trachyte of the Euganean Hills, subject of the present paper; in this regard, Germinario et al. [25], in a recent work, explored the link between the chang- ing petrophysical and mechanical properties of that stone and its diverse durability and resistance to water-driven weathering. Few studies have also focused on trachyte used in inland continental climates, as in Czech Republic [26] and Germany [27]. In particular, Graue et  al. [27] have examined weathering crusts of trachyte in industrial, urban and rural environments, showing how their thick- ness, grain size, and enrichment in heavy metals and other exogenous components well correlate with differ- ent degrees and sources of anthropogenic air pollution. In this paper, the problem of trachyte decay in urban environment is tackled investigating the mineralogi- cal, microstructural and chemical characteristics of weathering crusts and patinas detected on trachyte of the Euganean Hills used in the Renaissance city walls of Padua, in northern Italy. Trachyte alteration is discussed referring to environmental parameters, in particular concerning air quality and anthropic pollution sources, which are examined based on measured or modeled pol- lution data and placed in a cause-effect relationship with the weathering products. The influence of composition of the stone and other neighboring materials on specific weathering processes is also debated. The city walls of Padua Padua has a composite wall system surrounding the his- torical district gone through millennia of history and sev- eral layouts and building phases, dated to the Roman age, the Middle Ages (12th–14th century), and, finally, the Renaissance. The latest wall circuit, the best preserved today, was built roughly following the previous Medieval perimeter by the Republic of Venice Serenissima, an ancient state of northern Italy (697–1797). The supremacy of Serenissima in Padua began in 1405, but the works for new defensive walls started one century later, during and after the war with the League of Cambrai, an alliance formed in 1508 by the major European powers attempting to hinder the expansionist goals of Venice. The difficulties encoun- tered in defending Padua, the most important mainland city, and the ongoing technological military innovations forced Serenissima to plan the construction of a new fortification system. This started in 1513 and continued until half of the century, with the realization of walls with an 11 km perimeter, 19 bastions, 8 gates, and sev- eral bridges, protected by moats, rivers, and channels (Fig. 1). What can be seen today is the result of the exten- sive modifications and demolitions of several parts of the curtain walls and two gates occurred under urbanization pressure from the 19th century [28, 29]. The Renaissance wall system was built almost com- pletely using bricks for the outer surfaces, with a core filled with rubble of bricks and stones consolidated with mortar. Trachyte was used not only as stone blocks in the core. It was employed for stringcourses, parapets, ashlars on angular ends of the bastions and other minor elements, as well as for building some of the gates (Porta Savonarola, Porta San Giovanni, Porta Santa Croce, and Porta Liviana-Pontecorvo). A set of 22 trachyte samples was collected on four dif- ferent segments of the Renaissance walls for analyzing their weathering crusts and patinas. Stringcourses on curtains and roundels as well as ashlars of an angled bas- tion were sampled, their localization being indicated in Fig.  2. During sampling, spots with different exposure were chosen; in the case of stringcourses, samples from the upper, frontal and lower surface were collected. To our knowledge, no cleaning restoration intervention was ever carried out on the sampled stone elements. Page 3 of 17Germinario et al. Herit Sci (2017) 5:44 Euganean trachyte The trachyte used in the Renaissance walls was extracted in the quarry district of the Euganean Hills, a group of hills located near Padua formed by a sedimentary succes- sion of limestones and marls of the upper Jurassic—lower Oligocene, a Paleogene volcanic and hypabyssal series, and Quaternary detrital deposits. Trachytes are ascrib- able to a subvolcanic series dated to the lower Oligocene, and have acid to intermediate composition and moderate Na-alkaline affinity [30, 31]. From a petrographic point of view, Euganean trachyte is a holocrystalline to hypocrystalline rock with por- phyritic texture and a mineralogical composition given mostly by feldspars (anorthoclase, plagioclase, and sani- dine, in diverse combination), biotite and, occasionally, augite and kaersutite. The accessory minerals typically comprise quartz, cristobalite, Ti-magnetite, ilmenite, apatite, and zircon. Groundmass is composed by alkali- feldspar microlites usually with a felty texture, or some- times showing preferred orientations [32]. Fig. 1 The Renaissance city walls of Padua raised by the Republic of Venice Serenissima: a Porta Savonarola gate, with a wall segment; b Castel- nuovo circular bastion with a water gate facing a channel; c Cornaro pentagonal bastion Page 4 of 17Germinario et al. Herit Sci (2017) 5:44 The exploitation of Euganean trachyte started in Pre- Protohistory, but became more intense from Roman times. This material has been extensively used as carv- ing and building stone in northern and central Italy and nearby its borders. Querns, mortars, cippi, mile- stones, steles, urns, tombstones, and sarcophagi com- prise the most common artifacts crafted with trachyte all through the centuries. Euganean trachyte was widely used in the built environment too, as an instance for the admirable roads and other great infrastructure of the Roman age or the monumental architecture and construction from the Middle Ages and Renaissance. Indeed, with the rise of the Republic of Venice Serenis- sima, stone construction was given a substantial boost, and trachyte was largely employed in public buildings, churches, monasteries, monumental gates, defen- sive walls and private residences, as well as for paving squares and streets; the most striking examples can be admired in Padua and Venice ([32, 33] and references therein). Experimental methods The trachyte samples collected on the walls of Padua were analyzed in order to determine their mineralogical, microstructural and chemical characteristics, using the facilities of the Geoscience Center of Georg-August-Uni- versität Göttingen. Rock thin sections both parallel and perpendicular to the exposed surface were investigated with a polarized- light microscope and a field-emission scanning electron microscope (FE-SEM) FEI Quanta 200 FEG equipped with a ZrO/W Schottky field-emission gun and detec- tor for energy-dispersive X-ray spectroscopy (EDS). In addition to usual observations and phase identifications, carried out on gold-coated samples, the SEM was used for acquiring X-ray elemental maps of selected cross sections, operating at 20  kV acceleration voltage, and scanning a grid of 512 × 400 pixels with a dwell time of 300 ms. Powdery and incoherent samples were analyzed by X-ray powder diffraction (XRPD) with a Philips PW 1800 Fig. 2 The present-day circuit of the Renaissance city walls of Padua (satellite image from ©2016 Google), with sampling areas indicated, and two examples of weathering crusts and patinas on Euganean trachyte used for a stringcourse and as filling material in the wall core Page 5 of 17Germinario et al. Herit Sci (2017) 5:44 diffractometer equipped with Cu anode operating at 45 kV and 30 mA, measuring with scan steps of 0.02°2θ in the range 3–70°2θ and an integration time of 4 s. Furthermore, analyses by laser ablation inductively coupled plasma mass spectrometry (LA-ICPMS) were performed in order to determine major- and trace-ele- ment composition of both the altered layers and fresh host rock. The latter, prepared as polished samples embedded in epoxy, was analyzed with a Thermo Scien- tific Element 2 double-focusing magnetic-sector spec- trometer coupled to a Resonetics Resolution 193 nm Ar-F excimer laser; data were acquired along 1.5  mm-long profiles and average compositions calculated. Instead, the crusts and patinas were analyzed as they are, given the difficulty in preparing polished sections due to their lim- ited thickness. For these samples, a Perkin Elmer ELAN DRC II quadrupole spectrometer was used coupled to a Lambda Physik COMPex 110 193  nm Ar-F excimer laser. Data were acquired on profiles on the entire sample surface (centimetric in size) and average compositions calculated. Both lasers operated at 7  Hz repetition rate, 3 J/cm2 fluence, 7 µm/s velocity, and using a spot size of 120  µm. Element concentrations were calculated with Iolite v2.5 software package, by a script based on the fol- lowing procedure: the LA-ICPMS signal is first smoothed by ratioing to an appropriate denominator isotope pre- sent in the sample and standard (29Si); the element ratios are standardized with NIST 610 glass reference material; then, they are normalized to oxides sum to reach 100%, including all the elements [34]. Weathering analysis Mineralogy and microstructure Microscopic observations reveal that the thickness of the weathering crusts and patinas on the exposed surfaces is rather limited, often below few tens of micrometers, and only exceptionally may reach few hundreds of microm- eters. Sometimes, powdery and incoherent deposits are also observed. Almost all the samples have a high C content, respon- sible for the black-greyish color of many crusts and pati- nas. Subspherical carbonaceous particles may be isolated, grouped in small clusters (Fig.  3a), or form extensive layers, possibly displaying fractures and microcracks Fig. 3 SEM-BSE photomicrographs showing different features of the carbonaceous fraction (darker in the images) detected on the weathering crusts and patinas of Euganean trachyte and its microchemical composition by EDS measured on two different spots (signal from gold coating is also visible). a Cluster of subspherical carbonaceous particles. b Microcracked patina with crumbled fine-grained feldspars. c Carbonaceous mass with Fe oxides, carbonates, and quartz. d Aggregates of carbonaceous particles arranged along the edges and the internal fractures of a plagioclase phenocryst Page 6 of 17Germinario et al. Herit Sci (2017) 5:44 (Fig.  3b). Soot represents a container for further accu- mulation of pollutants, indeed it may be rich in heavy metals, especially Pb, or include exogenous quartz, alu- minosilicate minerals, chlorides, Al oxides, etc. The airborne carbonaceous pollutants are frequently trapped in crusts formed by microcrystalline calcite and, secondarily, dolomite (Fig. 4). The high concentration of these phases cannot be traced back to trachyte composi- tion, since they are originally present in low or negligi- ble amount. A high content of quartz is often detected as well. The carbonaceous particles may be also associated with a matrix rich in Fe, present as oxides and hydroxides or in amorphous state, giving a general brown-reddish color, in possible combination with carbonates (Fig. 3c). In the thinnest patinas, there are virtually no inter- mediate alteration layers between the host rock and the carbonaceous components, the adhesion of which takes place directly on the feldspars constituting the substrate; their fine grain size and crumbled appearance, which cre- ates a porous surface favoring C deposition, suggests for- mer processes of granular disintegration. C accumulates mainly on the groundmass or fine-grained phenocrysts, taking advantage of intercrystalline spaces and higher porosity, whereas large phenocrysts are less affected (Fig. 3d). Gypsum crusts are detected on a single sample, very close to a mortar splash by the joint of two trachyte blocks. Its collocation, on the lower side of a string- course, was a shelter against direct rainfall and washing out. The microscopic investigation revealed a complex stratigraphy (Fig.  5). The superficial layer is composed of a network of acicular or tabular gypsum crystals with rosette-like intergrowths, which embeds carbonaceous particles, but in rather low concentration. The second underlying layer is composed of amorphous silica. The third layer is constituted mostly of calcite, directly crys- tallized on the host rock. The presence of separate gyp- sum and calcite levels suggests a slow-rate alteration process, started with the crystallization and growth of a carbonate layer and its later, partial reaction with S, mostly limited to its outermost part. The gypsum layer represents a rather compact domain, whereas the under- lying host rock shows a high degree of fracturing. The XRPD analyses of powdery and incoherent depos- its sampled on trachyte confirm the occurrence of some of the mineral phases detected through the SEM obser- vations and microanalyses. Quartz, calcite, and dolomite are the major components, while the other identified phases comprise minerals from the host rock, like feld- spars and biotite, or from their alteration, such as illite and chlorite (Fig. 6). Major‑ and trace‑element composition The LA-ICPMS analyses of major elements (Table 1) sub- stantially confirm the occurrence of two main alteration types, characterized by a high concentration of calcite and Fe. If the average composition of Euganean trachyte in Germinario et al. [32] is taken as reference, the calcite crusts and patinas show an increase of CaO by a factor from 7 up to 60, corresponding to a maximum concen- tration of 86%. At the same time, a decrease in the con- tent of SiO2, Al2O3, Na2O, and K2O is always evident, up to a maximum of 87, 93, 97, and 98%, respectively. A modest increase of MgO, associated with dolomite pres- ence, is also noticeable. The different ratios between CaO Fig. 4 SEM–EDS X-ray maps of a calcite crust of Euganean trachyte prepared as epoxy-embedded cross section, with the exposed surface dis- played on the top (field size: 523.6 × 406.6 µm) Page 7 of 17Germinario et al. Herit Sci (2017) 5:44 and the feldspar-related elements reveal different degrees of alteration and homogeneity of the weathering layers, hence to what extent the silicate host rock has been oblit- erated by newly formed phases. As pointed out before, enrichment in carbonates and Fe may be associated but, when the latter is predominant, a Fe increase by a factor up to 6.5 is recorded. Although a general surface sulfation is often evident, only in the gypsum crust a large increase in SO3 is reported, by a factor of 2487, corresponding to a concentration of 25%, which almost completely hides the silicate composition of the host rock, in association with the high content of CaO. Further indications are given by the concentration of trace elements (a selection is reported in Table  2, while the complete dataset is included in Additional file 1). In comparison to the host rock, a remarkable enrichment in heavy metals of the crusts/patinas is evident (Fig.  7), especially in V, Cr, Ni, Cu, Zn, As, Cd, Sn, Sb, Pb, and Bi. As an instance, Pb results to be increased by a fac- tor of over 1700. The highest absolute concentrations are reported for Cu, Zn, and Pb, equal to 1009, 11,460, and 25,800  ppm, respectively. No significant mobilization of heavy metals into the host rock is detected [35]. As also summarized in Fig.  8, when the host rock is shielded by thick, homogeneous and well-developed crusts, as those rich in calcite or gypsum, the near-sur- face concentration of heavy metals is lower on average, i.e., the absorption of pollutants is more limited. Calcite and gypsum tend to form microcrystalline domains more compact than the underlying host rock, so that mecha- nisms of dry and wet deposition of pollutants are hin- dered. This is confirmed by a higher content of heavy metals on the stone surfaces exhibiting only a weak incip- ient alteration, maybe only recently exposed (e.g., due to previous detachment of outer layers). On the other hand, non-uniform crusts, which do not entirely cover the host rock, represent an intermediate condition: storage of airborne carbonaceous particles and surface accumu- lation of metallic pollutants are enhanced because of a relatively high porosity, given by a mix of disaggregated host rock and uneven, incomplete and scarcely adhering crystallization of newly formed phases. In this case, an Fig. 5 SEM–EDS X-ray maps of a gypsum crust of Euganean trachyte prepared as epoxy-embedded cross section, with the exposed surface displayed on the top (field size: 524.5 × 407.3 µm). Details of the gypsum crystals and the fractured host rock beneath the crust are showed in the SEM-BSE photomicrographs Page 8 of 17Germinario et al. Herit Sci (2017) 5:44 enrichment in CaO, Fe2O3, and heavy metals is clear, but the contribution of the silicate substrate to the chemical composition of the stone surface is still distinct. Finally, the relationship between trachyte sampling point and sample composition suggests the following considerations: the samples collected on the frontal sides of stringcourses or ashlars feature a higher concentration of carbonates on average, thus indicating a major inci- dence of calcite-rich alteration on vertical surfaces; the samples collected on the lower sides, including the gyp- sum crusts, display lower concentrations of heavy metals; no specific alteration trends dependent on the sampling site were recognized. Correlation with air quality Environmental setting In order to establish a correlation between trachyte alter- ation and air quality, it is necessary to describe the envi- ronmental setting the stone interacts with. Padua is a city of about 200,000 people in the Veneto region, northeastern Italy, located in the Po Plain about 20 km far from the Venetian Lagoon and 40 km from the coastline of the Adriatic Sea. The climate is humid temperate (Köppen classifica- tion: “Cfa”). It features hot summers, with record maxi- mum temperatures usually exceeding 35 °C, and mild to cold winters, when minimum temperatures may easily drop below 0  °C. The most humid period in the year is between fall and winter, whereas late-spring and summer months are the driest. Rainfall is concentrated during fall and spring, while winter has the lowest precipitation. Spring is usually the windiest season (Table 3). The pH value of rainfall is from 5.5 to 6 on average,1 which is the conventional value of unpolluted rainwater, i.e., 5.6 [36]. Concerning air quality, the most significant pollu- tion sources in Padua, besides road traffic and domes- tic combustion, are the only two major industrial plants in the city area, namely a waste-to-energy incinerator and a steel plant, about 3 and 6 km far from downtown, respectively. Compared to the pollution measured in background areas, traffic zones present a concentration of NOx increased by a factor of 1.5, whereas near indus- trial plants the same increase in the concentration of SO2 is registered, as well as an enrichment in heavy metals in the PM fraction, by a factor up to over 2 (Table 4). Finally, 1 No recent institutional data are available, so the value indicated has been assumed from alternative sources: dated measurements in Padua [16] and Venice (RIDEP network, 1988), as well as recent datasets from mountain localities in Veneto (CONECOFOR network and TESAF, Padua). For pro- posing that pH value, lower accuracy of dated analyses, sampling location, and the general reduction of emissions during the last decades have been taken into account. Fig. 6 XRPD spectrum of a powdery deposit on Euganean trachyte, showing a composition given mostly by quartz, calcite, and dolomite Page 9 of 17Germinario et al. Herit Sci (2017) 5:44 the influence of the industrial area of Venice-Porto Marghera, one of the largest coastal industrial zones in Europe, located 30 km far from Padua, cannot be ruled out. In its area of over 20 km2, chemical, petrochemical and petroleum industries, refineries, thermal power sta- tions, metallurgical industries, air separation and natural- gas processing plants, incinerators, etc. are operational. The emissions comprise mainly SO2, NOx, CO, PM, and VOC [37–39], which are easily transported to Padua by winds having usually a NE direction. Exogenous processes The mineralogical and chemical identity of the alterations of Euganean trachyte can be related to air pollution, so that composition of the weathering crusts and patinas turns out to be a marker for the relevant environmental conditions and their evolution. The enrichment in C and heavy metals can be traced back to the particulate deriving mostly from road traffic, emitted by diesel and gasoline-powered vehicles, and domestic combustion of woody biomass. These are the main sources of total suspended particulate (TSP) in Padua, according to the emission projections by ARPAV agency [40]2 summarized in Fig.  9. A further major 2 INEMAR projections by ARPAV agency contain space- and time-based estimations of the yearly emissions in the atmosphere generated by several anthropic and natural activities that, given the complexity and amount of the possible sources, could not be all exactly calculated. The estimations are based on both real measured data and theoretical indicators, the latter inferred from statistical data and exploratory surveys concerning popula- tion, territory, economy, development, etc. [40]. Table 1 Major-element chemical composition expressed as oxide weight percent of representative samples of Euganean trachyte from the Renaissance city walls of Padua determined by LA-ICPMS, on both surface (i.e., weathering crust or pat- ina) and host rock (inner part) The samples are divided by different types of alteration and sampling location as in Fig. 2 (SCR, Bastione Santa Croce; GAR, Torrione dell’Arena; CSN, Bastione Castelnuovo; FST, Torrione Venier) a  Bulk-rock chemical composition determined by X-ray fluorescence and averaged among 86 fresh trachyte samples collected on the Euganean Hills in 40 different quarries and outcrops [32] Sample SiO2 TiO2 Al2O3 Fe2O3 MnO MgO CaO Na2O K2O P2O5 SO3 Calcite-rich alteration SCR-01 Surface 8.57 0.02 1.14 0.58 0.04 1.49 85.85 0.17 0.12 0.69 0.38 Host rock 63.69 0.12 18.09 0.76 0.01 0.14 4.40 6.18 4.56 0.04 0.45 GAR-03 Surface 52.04 0.17 13.40 3.98 0.31 1.21 16.29 3.28 0.83 3.21 1.18 Host rock 67.17 0.09 18.08 0.91 0.00 0.20 1.51 5.75 5.70 0.12 0.10 CSN-03 Surface 55.10 0.40 11.59 3.51 0.09 1.51 15.60 3.00 0.97 1.42 2.93 Host rock 65.78 0.11 18.31 2.04 0.01 0.35 1.03 5.82 5.63 0.04 0.06 SCR-05 Surface 58.50 0.19 13.81 3.31 0.05 0.72 10.42 2.77 0.55 1.22 0.44 Host rock 67.89 0.30 15.96 1.97 0.02 0.59 1.69 5.26 5.21 0.17 0.12 Iron-rich alteration SCR-07 Surface 40.97 0.39 14.27 21.19 0.15 1.22 5.22 1.96 0.57 7.47 0.82 Host rock 68.09 0.15 17.23 1.34 0.02 0.40 1.21 5.32 5.64 0.10 0.08 Weak alteration FST-07 Surface 66.20 0.13 17.71 2.99 0.12 0.33 3.73 5.07 0.91 0.72 0.65 Host rock 69.08 0.06 16.46 0.84 0.01 0.12 2.01 5.20 4.33 0.07 0.11 Gypsum-rich alteration FST-05 Surface 5.44 0.01 0.41 0.11 0.00 0.17 66.07 1.34 0.12 0.58 24.87 Host rock 70.62 0.23 14.93 1.29 0.01 0.32 1.05 4.01 6.32 0.03 0.19 Average composition of Euganean trachytea 66.02 0.66 16.77 3.26 0.06 0.66 1.42 5.04 5.35 0.21 0.01 Page 10 of 17Germinario et al. Herit Sci (2017) 5:44 Ta bl e 2 Tr ac e- el em en t c he m ic al c om po si ti on e xp re ss ed a s  pp m o f r ep re se nt at iv e sa m pl es o f E ug an ea n tr ac hy te fr om  th e Re na is sa nc e ci ty w al ls o f P ad ua d et er - m in ed b y  LA -IC PM S, o n  bo th s ur fa ce (i .e ., w ea th er in g cr us t o r p at in a) a nd  h os t r oc k (in ne r p ar t) . O nl y a se le ct io n of  th e an al yz ed e le m en ts is s ho w ed (t he c om - pl et e da ta se t i s in cl ud ed in  A dd it io na l fi le  1 ) Th e sa m pl es a re d iv id ed b y di ffe re nt ty pe s of a lte ra tio n an d sa m pl in g lo ca tio n as in F ig . 2 (S CR , B as tio ne S an ta C ro ce ; G A R, To rr io ne d el l’A re na ; C SN , B as tio ne C as te ln uo vo ; F ST , T or rio ne V en ie r) a  B ul k- ro ck c he m ic al c om po si tio n de te rm in ed b y X- ra y flu or es ce nc e an d av er ag ed a m on g 86 fr es h tr ac hy te s am pl es c ol le ct ed o n th e Eu ga ne an H ill s in 4 0 di ffe re nt q ua rr ie s an d ou tc ro ps [3 2] Sa m pl e V Cr Co N i Cu Zn A s Cd Sn Sb Σ RE E Pb Bi Ca lc ite -r ic h al te ra tio n SC R- 01 S ur fa ce 23 .0 0 6. 50 2. 95 15 .8 0 26 1. 00 36 60 .0 0 25 .8 0 10 .5 0 13 .7 0 6. 29 48 .9 5 17 6. 60 0. 92 H os t r oc k 3. 49 2. 32 0. 68 1. 58 12 .0 9 57 .5 0 2. 40 0. 17 1. 58 0. 25 12 3. 34 8. 24 0. 05 G A R- 03 S ur fa ce 87 .2 0 11 5. 00 14 .7 0 75 .2 0 86 5. 00 10 42 .0 0 53 .9 0 11 .7 0 67 .6 0 25 .8 0 21 0. 83 58 7. 00 4. 93 H os t r oc k 3. 29 1. 14 1. 00 1. 51 15 .4 0 11 6. 70 1. 05 0. 68 1. 41 0. 11 61 .8 6 15 .5 0 0. 05 C SN -0 3 S ur fa ce 42 .3 0 84 .0 0 9. 70 58 .9 0 48 1. 00 52 3. 00 56 .0 0 3. 80 22 .9 0 6. 40 13 8. 93 38 9. 00 1. 14 H os t r oc k 4. 08 0. 64 1. 79 0. 96 8. 32 93 .3 0 1. 12 0. 24 1. 67 0. 22 61 .2 9 29 .3 0 0. 05 SC R- 05 S ur fa ce 42 0. 00 70 .0 0 7. 25 35 .5 0 35 2. 00 11 46 0. 00 55 .4 0 8. 85 50 .5 0 32 .6 0 19 9. 78 25 80 0. 00 2. 57 H os t r oc k 5. 46 10 .0 6 2. 78 1. 74 22 .6 0 15 82 .0 0 1. 98 0. 50 3. 74 0. 27 23 6. 71 8. 39 0. 05 Ir on -r ic h al te ra tio n SC R- 07 S ur fa ce 50 5. 00 21 1. 00 16 .5 0 72 .7 0 10 09 .0 0 62 10 .0 0 38 5. 00 63 .1 0 94 .6 0 34 .2 0 38 6. 86 24 90 0. 00 45 .5 0 H os t r oc k 2. 99 0. 79 1. 60 1. 50 30 .0 0 65 .8 0 1. 04 0. 15 0. 92 0. 17 13 0. 32 8. 21 0. 03 W ea k al te ra tio n FS T- 07 S ur fa ce 42 .5 0 5. 00 6. 80 48 .0 0 38 4. 00 87 1. 00 10 .6 0 5. 52 24 .4 0 6. 45 17 6. 81 28 0. 00 2. 33 H os t r oc k 1. 88 0. 78 1. 06 6. 50 18 .5 0 73 .4 0 0. 64 0. 24 1. 51 0. 13 65 .2 7 5. 46 0. 02 G yp su m -r ic h al te ra tio n FS T- 05 S ur fa ce 10 .2 7 3. 90 1. 28 4. 75 23 .8 0 24 .6 0 11 .0 0 0. 08 1. 45 1. 97 9. 88 22 .1 3 0. 10 H os t r oc k 10 .1 0 1. 26 1. 73 2. 42 16 .1 0 41 .5 0 2. 04 0. 19 2. 28 0. 30 14 9. 32 10 .5 2 0. 06 A ve ra ge c om po si tio n of E ug an ea n tr ac hy te a 23 3 3 2 23 10 3 n/ a n/ a n/ a n/ a n/ a 15 n/ a Page 11 of 17Germinario et al. Herit Sci (2017) 5:44 source of particulate is fuel-free industrial processes in the steel mill (“productive processes”); as indicated in Table 4, its emissions have a relatively high content of Pb, Ni, and As, so this can be directly related to the enrich- ment in heavy metals detected on the weathering crusts. By comparison, TSP produced by the local incinerator (“waste treatment and disposal”) is almost negligible. If the contribution from the industrial area of Venice-Porto Marghera is also considered, a further supply of carbona- ceous pollutants and heavy metals can be identified mainly from the power stations, refinery, petroleum industries, and the related employment of fuels and machines. Conditions of high air humidity and precipitation and strong wind are the most favorable for pollutant dispersion, so that summer can be considered the least dangerous season. Carbonaceous and metallic particles act as catalysts, so their accumulation enhance further stone alteration and crust growth [41]. Among other exogenous processes contributing to the weathering of Euganean trachyte, it is worth mentioning the possible reactions leading to the formation of the car- bonate crusts. Considering the originally low concentra- tion of calcite and dolomite in the host rock, the only plausible and consistent source for these phases is identi- fied in lime and Mg-lime mortars used in the walls of Padua for joining trachyte blocks. Indeed, Ca carbonate Fig. 7 Time-resolved LA-ICPMS spectrum obtained from a Fe-rich crust of Euganean trachyte, by a combined profile and spot analysis: crust surface was first ablated along a line and eventually drilled through, until reaching the host rock Fig. 8 Comparison of the major- and trace-element composition measured by LA-ICPMS on the weathering crusts and patinas of representative samples of Euganean trachyte. Sample names and compositions refer to Tables 1 and 2 Page 12 of 17Germinario et al. Herit Sci (2017) 5:44 may be dissolved from mortars by acid solutions and reprecipitate in basic ones; calcite is less stable, i.e., its dissolution is faster, when pH is lower than about 5–6: dissolution rate increases with increasing H+ activity, in high-acidity regime, or CO2 partial pressure, in low-acid- ity regime [42–44]. As reported above, average pH of rainfall in Padua is around 5.5–6, just around the limit of calcite stability. This means that pH fluctuations3 to higher acidity may increase leachability of Ca carbonate from mortars; the resulting solution containing leached Ca(OH)2, thus an alkaline medium [36], continues its short-range path, and may easily reach trachyte elements (especially subvertical substrates), wetting their surface and penetrating into pores; finally, calcite reprecipitates, taking advantage of the alkaline pH. Carbonate recrystal- lization episodes might be more common in summer- time, whereas dissolution process possibly takes place more frequently during late fall and winter: in the cold season, atmosphere acidity is generally higher due to domestic heating and related emissions, and low temper- atures increase calcite solubility [45]; higher humidity and precipitation represent other favorable factors, as well as the recurrence of misty days, with fog being more acid than rainfall, with pH even below 4 [13, 36]. The role of neighboring mortars acting as Ca source for trachyte weathering has been outlined by previous studies too [21, 22, 27]. It seems to be confirmed also 3 pH fluctuations of an aqueous solution can occur due to leaching of stones/mortars or solubilization of acid particles previously dry-deposited on their surface. Fluctuations also depend on the current general air qual- ity and other large-scale factors: for example, a short drizzle or the initial stage of a rainfall are more acid, since the highly-soluble anthropogenic pol- lutants are first gathered; in a later stage, airborne alkaline agents reacting with slower kinetics and solubility—e.g., NH3 from agricultural fertilizers, soil particles, wind-transported Saharan dust, etc.—make water pH increase [15, 16]. by the formation of the gypsum crusts very close to a mortar joint, and the possible supply of quartz, sulfates, chlorides, etc. from the mortar aggregate. The layers of amorphous silica might develop from the dissolution of either the mortar or the rock-forming silicate minerals or glass-bearing domains in trachyte [46]. Quartz might be also derived by Saharan dust, long-range transported from Africa by Sirocco: when this wind rises to pass over the Alps further north than Padua, the desert particles, composed of silicates and carbonates, are scavenged by rainfall and may precipitate in the Po Plain [15, 16]. On the other hand, the gypsum crusts might be also connected to anthropogenic air pollutants, i.e., to SO2 oxidation and hydration and the well-known subsequent reaction of H2SO4 with a Ca carbonate substrate, in this case formed on trachyte after mortar leaching. The high degree of fracturing of the underlying host rock suggests an initial penetration of Ca-rich solutions in the outer pores, then producing crystallization pressures during water evaporation up to rock failure. Gypsum possibly formed after subsequent Ca loading and growing out- wards of the carbonate crystallization layer, on surfaces sheltered from direct rainfall and washing out. Concern- ing SO2 supply, the most important contribution is given by the emissions of the steel mill. Anyway, the overall concentration of SO2 is rather low in Padua and not com- parable to that typical of big urban and industrial centers [13], and presumably it was so even in the past. This— other than the carbonate-poor composition of trachyte— justifies the very limited extension of the gypsum crusts and their rare occurrence [47]. A hypothesis that can be completely discarded is the nucleation of gypsum directly from soot absorbing pollutants [48], given its low con- centration and, on the other hand, the large extension of the gypsum crusts. Table 3 Climatic parameters measured in Padua averaged from 2000 to 2015. Source: ARPAV Climatic parameter Value Climatic parameter Value Temperature (°C) Precipitation (mm) Annual mean 14.5 Annual total 959 Annual mean min 10.7 Lowest annual total 561 Annual mean max 19.1 Highest annual total 1395 Lowest monthly mean and monthly mean min (month) 3.9/1.5 (January) Lowest monthly total (month) 58 (January) Highest monthly mean and monthly mean max (month) 24.7/30.2 (July) Highest monthly total (month) 107 (November) Relative humidity (%) Precipitation days Annual mean 74 Annual total (≥ 1 mm) 84 Annual mean min 53 Annual mean max 91 Solar irradiance (MJ/m2) Lowest monthly mean and monthly mean min (month) 65/43 (July) Annual total (Legnaro, 1994–2015) 5005 Highest monthly mean and monthly mean max (month) 84/94 (November) Wind direction Annual mean NE Page 13 of 17Germinario et al. Herit Sci (2017) 5:44 Ta bl e 4 Co nc en tr at io n of  a ir p ol lu ta nt s m ea su re d in  P ad ua in  d iff er en t l oc at io ns a nd  e xp re ss ed a s  ho ur ly g ra nd m ea ns , f or  g as eo us p ol lu ta nt s, a nd  d ai ly g ra nd m ea ns , f or   P M 10 . S ou rc e: A RP AV Th e re co rd s co m pr is e th e fo llo w in g pe rio ds : f or g as eo us p ol lu ta nt s, fr om 2 00 0 to 2 01 5 (B ac kg ro un d an d Tr affi c st at io ns ) a nd fr om 2 00 1 to 2 01 5 (In du st ria l I I s ta tio n) ; f or P M 10 , f ro m 2 00 3 to 2 01 5 (B ac kg ro un d, T ra ffi c an d In du st ria l I s ta tio ns ) a nd fr om 2 00 8 to 2 01 5 (In du st ria l I I s ta tio n) In du st ria l I : o ne s ta tio n m on ito rin g th e em is si on s fr om a lo ca l s te el m ill In du st ria l I I: tw o st at io ns m on ito rin g th e em is si on s fr om a lo ca l w as te -t o- en er gy in ci ne ra to r M ea su re m en t s ta tio n CO (m g/ m 3 ) N O (µ g/ m 3 ) N O 2 (µ g/ m 3 ) Σ N O x (µ g/ m 3 ) SO 2 (µ g/ m 3 ) O 3 (µ g/ m 3 ) PM 10 (µ g/ m 3 ) A s (n g/ m 3 ) Cd (n g/ m 3 ) N i (n g/ m 3 ) Pb (n g/ m 3 ) C 6 H 6 (µ g/ m 3 ) C 2 0H 12 (n g/ m 3 ) PM 10 c om po si tio n Ba ck gr ou nd W ho le re co rd 0. 7 29 .9 42 .1 88 .4 2. 5 52 .5 43 .0 1. 4 0. 9 3. 4 17 .7 2. 1 1. 3 L as t 5 y ea rs (2 01 1– 20 15 ) 0. 6 23 .0 34 .8 69 .6 1. 6 51 .7 39 .3 0. 7 0. 4 3. 5 9. 7 1. 7 1. 4 Tr affi c W ho le re co rd 0. 8 53 .2 53 .0 13 2. 6 2. 4 45 .2 43 .4 1. 5 1. 0 3. 8 17 .4 3. 3 1. 3 L as t 5 y ea rs (2 01 1– 20 15 ) 0. 4 29 .8 44 .0 89 .8 2. 4 45 .6 36 .8 0. 8 0. 5 3. 6 9. 7 3. 6 1. 2 In du st ria l I W ho le re co rd n/ a n/ a n/ a n/ a n/ a n/ a 43 .0 1. 5 1. 3 6. 7 45 .2 n/ a 1. 2 L as t 5 y ea rs (2 01 1– 20 15 ) n/ a n/ a n/ a n/ a n/ a n/ a 37 .9 1. 0 0. 5 4. 1 21 .3 n/ a 1. 3 In du st ria l I I W ho le re co rd 0. 7 35 .0 42 .2 95 .9 3. 7 39 .4 37 .2 0. 9 0. 5 3. 0 10 .0 n/ a 1. 1 L as t 5 y ea rs (2 01 1– 20 15 ) 0. 6 26 .6 38 .7 79 .6 1. 8 43 .0 36 .0 0. 9 0. 5 3. 0 9. 3 n/ a 1. 3 Page 14 of 17Germinario et al. Herit Sci (2017) 5:44 Finally, it is worth reminding that no evident effect of interaction between trachyte and sea salts carried by wind or rainwater was noticed. Indeed, the typical weathering products connected to coastal environment identified in previous studies [22, 23], in particular high concentrations of halite, were not found here. The scant chlorides detected have to be traced back to mortar com- position instead, as stated above. On the other hand, composition of the weathering products of Euganean trachyte can be compared to that detected in inland environment on Drachenfels trachyte studied by Graue et al. [27]. The main difference lies in a greater incidence of CaO enrichment and calcite recrys- tallization on surface alteration of Euganean trachyte, whereas the framboidal crusts analyzed on Drachen- fels trachyte in an urban and industrial setting generally are thicker (centimetric size), richer in well-developed gypsum crystals, and may show stronger sulfation and higher concentration of heavy metals. Nevertheless, if Pb concentration is the term for comparison, that analyzed in the crusts and patinas of Euganean trachyte is often close to the typical values measured in European cities, i.e., from few hundreds ppm up to 2000 ppm [27]. Stone leaching Some features of the weathering crusts and patinas of Euganean trachyte can be explained by intrinsic fac- tors, in particular the Fe-rich alterations. Microscopic examinations disclosed an enrichment in fine-grained Fe oxides and hydroxides and amorphous Fe in the proxim- ity of biotite phenocrysts and, secondarily, magnetite and ilmenite crystals (Fig. 10). This suggests Fe mobilization from the minerals by leaching and migration to surface, forming brown-reddish alteration layers. Leaching might have also occurred at the expense of mafic xenoliths [23] or pervasive migration fronts of Fe oxides/hydrox- ides, genetically linked to post-magmatic processes [32]. Leaching of biotite seems more likely, since solubility of Fig. 9 Estimated emissions of the major air pollutants in Padua during 2010 by several macro-groups of anthropic and natural activities, and com- parison with emissions calculated for Venice in the same year, mainly deriving from the industrial area of Porto Marghera (INEMAR projections [40]) Page 15 of 17Germinario et al. Herit Sci (2017) 5:44 magnetite and ilmenite is lower. Fe2+ release from the octahedral layers of biotite is strongly pH dependent: rate of dissolution linearly increases with decreasing pH, but the reaction is significant only for values lower than 4–5 [49–51]. The environmental conditions leading to the formation of the Fe-rich crusts and patinas would be sim- ilar to those described for the calcite crusts, involving pH fluctuations around the limit of the stability field even of biotite; in this case, however, its lower leachability if com- pared to that of calcite requires a more acid environment for dissolution to get started. Finally, a minor contribu- tion of PM to Fe enrichment of trachyte surfaces must be taken into account, however that is not the main source, as also confirmed by the absence of Fe compounds in the incoherent and powdery surface deposits of exogenous origin. A leaching process of the host-rock has been supposed also with regard to dissolution of plagioclase and release of Ca2+ cations, as an alternative or concurrent mecha- nism of formation of the calcite crusts. In Euganean tra- chyte, plagioclase represents one of the main mineral phases, it has a prevalent oligoclase–andesine compo- sition with an average CaO content of 6% [32], so theo- retically it is a possible source of Ca [52, 53]. However, the overall CaO content of the bulk rock is rather low on average (1.4%, see Table 1). Additionally, in acid solu- tions, Ca leachability from plagioclase is rather low, espe- cially taking calcite as a term of comparison or even Fe release from biotite [46, 54]. Leaching is also facilitated in fine-grained crystals, whereas plagioclases are among the coarsest phenocrysts in Euganean trachyte, even reach- ing a centimetric size. Moreover, clay minerals, typically resulting from feldspar alteration, were detected only in minor amounts (their concentration in the host rock is also rather low or negligible). For all these reasons, plagi- oclase cannot be considered the primary source of such a high concentration of carbonates in the crusts, although its contribution cannot be totally excluded. Conclusions The crusts and patinas of Euganean trachyte related to urban weathering have mostly limited thickness and extension. They are rich in heavy metals and carbona- ceous matter, which promote further accumulation of pollutants, mainly derived from fuel use in road trans- port and domestic combustion, and, secondarily, short- and medium-range industrial emissions. These products are typically embedded in matrixes rich in calcite or Fe (either as oxides/hydroxides or amorphous components). The crusts and patinas also include grains of quartz, dolomite, and other minor components, such as metallic and aluminum–silicon particles, chlorides, etc. The high concentration of carbonates cannot derive from host rock components; pH-controlled dissolution, mobiliza- tion, and recrystallization of carbonates from nearby lime mortars used in joints seems the most plausible source of Ca. This process may also occur on seasonal basis, depending on pH fluctuations. A secondary and very limited source of Ca can be represented by dissolution of plagioclases. A more likely intrinsic process of alteration affects biotite and other Fe-bearing minerals, through pH-dependent leaching of Fe and its migration to surface. Other alteration forms recognized comprise powdery deposits and gypsum crusts, but they do not occur com- monly. The latter possibly derive from the contribution of SO2 pollutant, having a rather low concentration in the air though; the presence of sulfate impurities in mortar aggregate and their leaching can be alternatively invoked. Fig. 10 Thin-section photomicrographs of samples of Euganean trachyte with Fe-rich crusts, showing dispersion of fine-grained Fe oxides/hydrox- ides or Fe in amorphous state around a biotite crystal (left) and two opaque minerals (i.e., magnetite or ilmenite) (right), apparently indicating near-surface mineral leaching Page 16 of 17Germinario et al. Herit Sci (2017) 5:44 When present, thick, homogeneous and well-developed crusts, rich in either calcite or gypsum, partially shield the host rock from further pollutant absorption. From this study, it arises that most of the alteration products of Euganean trachyte are due to exogenous pro- cesses, whereas the stone itself does not have particular compositional features prone to trigger major danger- ous mechanisms of decay. Generally, composition of the weathering crusts and patinas of Euganean trachyte proves to be an informative marker for the relevant envi- ronmental conditions and their evolution, with a strict link with air pollution determined by different anthropic pollution sources. Further studies are needed concerning trachyte-mortar interaction, in order to explore to what extent mortar affects stone surface alteration and in which microcli- matic conditions, what is the mobilization potential of the leached components, and the influence of different mortar recipes. Abbreviations EDS: energy-dispersive X-ray spectroscopy; FE-SEM: field-emission scanning electron microscope; LA-ICPMS: laser ablation inductively coupled plasma mass spectrometry; PM: particulate matter; SEM: scanning electron micro- scope; TSP: total suspended particulate; VOC: volatile organic compounds; XRPD: X-ray powder diffraction. Authors’ contributions This paper has been extracted from the Ph.D. thesis written by LG, after a research work supervised by CM and co-supervised by LM at the University of Padova. SS supervised the research activities carried out at the University of Göttingen. Finally, KS provided support for the LA-ICPMS analyses. All authors read and approved the final manuscript. Author details 1 Department of Geosciences, University of Padova, Via Gradenigo 6, 35131 Padua, Italy. 2 Geoscience Center, Georg-August-Universität Göttingen, Goldschmidtstrasse 3, 37077 Göttingen, Germany. Acknowledgements The authors thank Kirsten Techmer and Klaus Wemmer (Uni. Göttingen) for their support during the SEM and XRPD analyses, respectively. The authors are very grateful to Hans Ruppert (Uni. Göttingen) for the helpful discussions on the results. The review and comments on an early draft of the manuscript by Giuseppe Cultrone (Uni. Granada) are also much appreciated. Thanks are due to Comune di Padova for kindly authorizing sampling on the city walls and to Comitato Mura di Padova, in particular Fabio Bordignon, for provid- ing information on the building phases and past conservation interventions. Finally, ARPAV agency is acknowledged for providing the climatic and air qual- ity data, and Dario Camuffo (CNR-ISAC, Padova) and Michela Rogora (CNR-ISE, Verbania) for further information on local environmental parameters. Additional file Additional file 1. Trace-element chemical composition expressed as ppm of representative samples of Euganean trachyte from the Renais- sance city walls of Padua determined by LA-ICPMS, on both surface (i.e., weathering crust or patina) and host rock (inner part). The samples are divided by different types of alteration and sampling location as in Fig. 2 (SCR, Bastione Santa Croce; GAR, Torrione dell’Arena; CSN, Bastione Castel- nuovo; FST, Torrione Venier). Competing interests The authors declare that they have no competing interests. Availability of data and materials An extra database of chemical data is provided as supplementary on-line material (“Additional file 1”). Consent for publication Not applicable. Ethics approval and consent to participate Not applicable. Funding University of Padova (Research Project No. CPDA151883/15 of CM), DAAD (German Academic Exchange Service, Short-Term Research Grants 2016– 57214227 to LG), European Union (Erasmus + grant to LG). Publisher’s Note Springer Nature remains neutral with regard to jurisdictional claims in pub- lished maps and institutional affiliations. Received: 30 June 2017 Accepted: 13 September 2017 References 1. Brimblecombe P, Camuffo D. Long term damage to the built environ- ment. In: Brimblecombe P, editor. The effects of air pollution on the built environment, vol. 2. London: Imperial College Press; 2003. p. 1–30 (Air Pollution Reviews). 2. Brimblecombe P. Environment and architectural stone. In: Siegesmund S, Snethlage R, editors. Stone in architecture. Properties, durability. 5th ed. Berlin: Springer; 2014. p. 317–47. 3. Sohn I. Long-term energy projections: what lessons have we learned? Energy Policy. 2007;35:4574–84. 4. Wolde-Rufael Y. Coal consumption and economic growth revisited. Appl Energy. 2010;87:160–7. 5. Thomas LP. Coal resources and reserves. In: Osborne D, editor. The coal handbook: towards cleaner production, vol. 1. Amsterdam: Elsevier, Woodhead Publishing Series in Energy; 2013. p. 80–106. 6. Tollefson J. How Trump plans to wipe out Obama-era climate rules. Nature. 2017. doi:10.1038/nature.2017.21726. 7. Guerreiro CBB, Foltescu V, de Leeuw F. Air quality status and trends in Europe. Atmos Environ. 2014;98:376–84. 8. Grossi CM, Brimblecombe P. Effect of long-term changes in air pollution and climate on the decay and blackening of European stone buildings. In: Přikryl R, Smith BJ, editors. Building stone decay: from diagnosis to conservation, vol. 271. London: Geological Society, Special Publications; 2007. p. 117–30. 9. Auras M, Beer S, Bundschuh P, Eichhorn J, Mach M, Scheuvens D, Schorling M, von Schumann J, Snethlage R, Weinbruch S. Traffic-related immissions and their impact on historic buildings: implications from a pilot study at two German cities. Environ Earth Sci. 2013;69:1135–47. 10. Saiz-Jimenez C. Organic pollutants in the built environment and their effect on the microorganisms. In: Brimblecombe P, editor. The effects of air pollution on the built environment, vol. 2. London: Imperial College Press; 2003. p. 183–226 (Air Pollution Reviews). 11. Saiz-Jimenez C. Deposition of airborne organic pollutants on historic buildings. Atmos Environ. 1993;27B(1):77–85. 12. Sabbioni C. Contribution of atmospheric deposition to the formation of damage layers. Sci Total Environ. 1995;167:49–55. 13. Charola AE, Ware R. Acid deposition and the deterioration of stone: a brief review of a broad topic. In: Siegesmund S, Weiss T, Vollbrecht A, editors. Natural stone, weathering phenomena, conservation strategies and case studies, vol. 205. London: Geological Society, Special Publications; 2002. p. 393–406. Page 17 of 17Germinario et al. Herit Sci (2017) 5:44 14. Watt J, Hamilton R. The soiling of buildings by air pollution. In: Brimble- combe P, editor. The effects of air pollution on the built environment, vol. 2. London: Imperial College Press; 2003. p. 289–334 (Air Pollution Reviews). 15. Camuffo D, Del Monte M, Ongaro A. The pH of the atmospheric precipita- tion in Venice, related to both the dynamics of precipitation events and the weathering of monuments. Sci Total Environ. 1984;40:125–39. 16. Camuffo D, Bernardi A, Zanetti M. Analysis of the real-time measurement of the pH of rainfall at Padova, Italy: seasonal variation and meteorologi- cal aspects. Sci Total Environ. 1988;71:187–200. 17. Camuffo D. Physical weathering of stones. Sci Total Environ. 1995;167:1–14. 18. Sabbioni C. Mechanisms of air pollution damage to stone. In: Brimble- combe P, editor. The effects of air pollution on the built environment, vol. 2. London: Imperial College Press; 2003. p. 63–106 (Air Pollution Reviews). 19. Grissom CA. The deterioration and treatment of volcanic stone: a review of the literature. In: Charola AE, Koestler RJ, Lombardi G, editors. Proceed- ings of the international meeting “Lavas and Volcanic Tuffs”, Easter Island, Chile, 25–31 October 1990. p. 3–29. 20. St Seymour K, Sahin Guchan N, Lamera S, Hatziapostolou A, Kouli M, Vam- voukakis C. Romancing the stone: construction of monuments & works of art from volcanic rock. In: Proceedings of the 7th pan-hellenic geographi- cal conference of the Hellenic Geographical Association, Mytilene, Lesvos, Greece, 14–17 October 2004. E1K164. 21. Prudêncio MI, Waerenborgh JC, Gouveia MA, Trindade MJ, Alves E, Seque- ira Braga MA, Alves CA, Figueiredo MO, Silva T. Degradation processes of trachytes in monument façades, Azores, Portugal. In: Arehart GB, Hulston JR, editors. Water–rock interaction. Rotterdam: Balkema; 1998. p. 391–4. 22. Alves CAS, Sequeira Braga MA, Trancoso A. Saline pollution in trachyte monuments of the Azores Islands (Portugal). In: Fassina V, editor. Proceed- ings of the 9th international congress on deterioration and conservation of stone, Venezia, Italy, 19–24 June 2000. p. 225–33. 23. Lazzarini L, Antonelli F, Cancelliere S, Conventi A. The deterioration of Euganean trachyte in Venice. In: Lukaszewicz JW, Niemcewicz P, editors. Proceedings of the 11th international congress on deterioration and conservation of Stone, Torun, Poland, 15–20 September 2008. p. 153–63. 24. Langella A, Calcaterra D, Cappelletti P, Colella A, D’Albora MP, Morra V, De Gennaro M. Lava stones from Neapolitan volcanic districts in the architec- ture of Campania region, Italy. Environ Earth Sci. 2009;59:145–60. 25. Germinario L, Siegesmund S, Maritan L, Mazzoli C. Petrophysical and mechanical properties of Euganean trachyte and implications for dimen- sion stone decay and durability performance. Environ Earth Sci. 2017. doi:10.1007/s12665-017-7034-6. 26. Gillhuber S, Lehrberger G, Thuro K. Teplá trachyte weathering phenom- ena and physical properties of a rare volcanogenic building stone. In: Proceedings of IAEG 2006—engineering geology for tomorrow’s cities, Nottingham, UK, 6–10 September 2006. 469, p. 1–11. 27. Graue B, Siegesmund S, Oyhantcabal P, Naumann R, Licha T, Simon K. The effect of air pollution on stone decay: the decay of the Drachenfels trachyte in industrial, urban, and rural environments—a case study of the Cologne, Altenberg and Xanten cathedrals. Environ Earth Sci. 2013;69:1095–124. 28. Mazzi G, Verdi A, Dal Piaz V. Le mura di Padova. Percorso storico-architet- tonico. Padova: Il Poligrafo; 2002. 29. Fadini U, editor. Mura di Padova. Guida al sistema bastionato rinascimen- tale. Vicenza: In Edibus; 2013. 30. Milani L, Beccaluva L, Coltorti M. Petrogenesis and evolution of the Euganean Magmatic Complex, Veneto region, north-east Italy. Eur J Miner. 1999;11:379–99. 31. Bartoli O, Meli S, Bergomi MA, Sassi R, Magaraci D, Liu DY. Geochemistry and zircon U–Pb geochronology of magmatic enclaves in trachytes from the Euganean Hills (NE Italy): further constraints on Oligocene magma- tism in the eastern southern Alps. Eur J Miner. 2015;27:161–74. 32. Germinario L, Hanchar JM, Sassi R, Maritan L, Cossio R, Borghi A, Maz- zoli C. New petrographic and geochemical tracers for recognizing the provenance quarry of trachyte of the Euganean Hills, northeastern Italy. Geoarchaeology 2017; (in press). 33. Germinario L, Zara A, Maritan L, Bonetto J, Hanchar JM, Sassi R, Sieges- mund S, Mazzoli C. Tracking trachyte on the Roman routes: provenance study of Roman infrastructure and insights into ancient trades in north- ern Italy. Geoarchaeology 2017; (in press). 34. Simon K. LA-ICP-MS transient signal quantification of NIST, USGS and MPI-DING glasses by ratioing, standardization, normalization and correc- tion (RSNC). Germany: Geowissenschaftliches Zentrum, Georg-August- Universität Göttingen; 2015 (Unpublished). 35. Török Á, Licha T, Simon K, Siegesmund S. Urban and rural limestone weathering; the contribution of dust to black crust formation. Environ Earth Sci. 2011;63:675–93. 36. Steiger M, Charola AE, Sterflinger K. Weathering and deterioration. In: Siegesmund S, Snethlage R, editors. Stone in architecture. Properties, durability. 5th ed. Berlin: Springer; 2014. p. 225–316. 37. ARPAV. Rapporto ambientale d’area di Porto Marghera—bilancio ambien- tale 1998–2007. Venezia: ARPAV; 2007. 38. ARPAV. Tavolo tecnico cementifici—1° rapporto tecnico. Padova: ARPAV; 2009. 39. ARPAV. Monitoraggio della qualità dell’aria presso il termovalorizzatore di San Lazzaro—relazione tecnica. Padova: ARPAV; 2015. 40. ARPAV. Inventario regionale delle emissioni in atmosfera INEMAR Veneto 2010—relazione generale. Venezia: ARPAV; 2015. 41. Simão J, Ruiz-Agudo E, Rodriguez-Navarro C. Effects of particulate matter from gasoline and diesel vehicle exhaust emissions on silicate stones sulfation. Atmos Environ. 2006;40:6905–17. 42. Fredd CN, Fogler HS. The kinetics of calcite dissolution in acetic acid solu- tions. Chem Eng Sci. 1998;53(22):3863–74. 43. Arvidson RS, Evren Ertan I, Amonette JE, Luttge A. Variation in calcite dissolution rates: a fundamental problem? Geochim Cosmochim Acta. 2003;67(9):1623–34. 44. Dolgaleva IV, Gorichev IG, Izotov AD, Stepanov VM. Modeling of the effect of pH on the calcite dissolution kinetics. Theor Found Chem Eng. 2005;39(6):614–21. 45. Deer WA, Howie RA, Zussman J. An introduction to the rock-forming minerals. 3rd ed. London: The Mineralogical Society; 2013. 46. Brantley SL, Olsen AA. Reaction kinetics of primary rock-forming minerals under ambient conditions. In: Holland HD, Turekian KK, editors. Treatise on geochemistry, vol. 7. 2nd ed. Amsterdam: Elsevier; 2014. p. 69–113. 47. Germinario L, Andriani GF, Laviano R. Petrography, mineralogy, chemi- cal and technical properties of the building stone of Ostuni Cathedral (Italy): inferences on diagnostics and conservation. Period Miner. 2014;83(3):379–400. doi:10.2451/2014PM0021. 48. Camuffo D. Deterioration processes of historical monuments. In: Schnei- der T, editor. Acidification and its policy implications. Amsterdam: Elsevier; 1986. p. 189–221. 49. Acker JG, Bricker OP. The influence of pH on biotite dissolution and alteration kinetics at low temperature. Geochim Cosmochim Acta. 1992;56:3073–92. 50. Bray AW, Benning LG, Bonneville S, Oelkers EH. Biotite surface chemistry as a function of aqueous fluid composition. Geochim Cosmochim Acta. 2014;128:58–70. 51. Bray AW, Oelkers EH, Bonneville S, Wolff-Boenisch D, Potts NJ, Fones G, Benning LG. The effect of pH, grain size, and organic ligands on biotite weathering rates. Geochim Cosmochim Acta. 2015;164:127–45. 52. Blum AE, Stillings LL. Feldspar dissolution kinetics. In: White AF, Brantley SL, editors. Chemical weathering rates of silicate minerals, vol. 31. Wash- ington, DC: Mineralogical Society of America; 1995. p. 291–351 (Reviews in mineralogy). 53. White AF, Buss HL. Natural weathering rates of silicate minerals. In: Hol- land HD, Turekian KK, editors. Treatise on geochemistry, vol. 7. 2nd ed. Amsterdam: Elsevier; 2014. p. 115–55. 54. Snäll S, Liljefors T. Leachability of major elements from minerals in strong acids. J Geochem Explor. 2000;71:1–12.